Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
While troubleshooting a connectivity issue on a Branch router, you realize that it is not forming a neighbor relationship with the HQ router. What statements are correct about OSPF neighbors? (Choose two) A. A successful ping from the Branch router to the HQ router will indicate IP connectivity between the two B. The [show ip interface brief] command verifies layer 3 connectivity C. Use the [show ip interface brief] command to verify that the status and protocol on the interface is up D. Regardless of the OSPF area configured, the neighbor adjacency will form if layer 2 and layer 3 connectivity is established https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/troubleshooting-multiarea-ospf.html Which command is used to disable unused switchports? A. no shutdown B. off C. disable D. shutdown E. quit Which command will you use to verify that an IPv4 address has been applied to an interface in the correct direction? A. show access-list B. show interface C. show ip interface D. show ip interface brief E. show access-list interfaces F. show access-group Which statement about VLAN operation on Cisco Catalyst switches is true? A. When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table. B. Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN. C. Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN. D. Ports between switches should be configured in access mode so that VLANs can span across the ports. https://www.learncisco.net/courses/icnd-1/ethernet-lans/developing-design-for-layer-2.html Imagine you configured OSPFv2 in a small lab network. Which of the following answers list a condition that could keep the routers in your lab from learning all the routes to all the IPv4 routes in your small lab network? (Choose two) A. An ACL could be blocking router advertisements. B. Two neighboring routers that connect to the same link have been configured with the same OSPF area and with the same IPv4 subnet mask. C. Any physical layer problem that would prevent two neighboring routers from being able to ping each others IPv4 addresses in the subnet that exists between the two routers. D. Two neighboring routers that connect to the same link have been configured with the same OSPF process ID on the router ospf command. Which command is used to verify the DHCP relay agent address that has been set up on your Cisco IOS router? A. show ip interface brief B. show ip dhcp bindings C. show ip route D. show ip interface E. show interface F. show ip dhcp pool Review the topology. All subnets exist in OSPF area 0. Which command, if issued on R3, would show all the LSAs known by R3? A. Show running-config B. Show ip ospf interface C. Show ip ospf neighbors D. Show ip route ospf E. Show ip ospf database Regarding lightweight AP modes, which one of the following is true? A. An AP can operate in multiple modes at the same time. B. An AP only has one possible mode of operation. C. The Run mode is the default mode. D. The SE-Connect mode is used for spectrum analysis. A network uses an SDN architecture with switches and a centralized controller. Which of the following terms describes a function or functions expected to be found on the switches but not on the controller? A. A Northbound Interface B. A Southbound Interface C. Data plane functions D. Control plane functions Which command can be used to help disable multiple ports on a switch at the same time? A. interface range B. default interface C. interface range shutdown D. shutdown range Which of the following statements are valid for a broadcast domain? (Choose two) A. The network portion of an IP address connecting two devices cannot be reused again within the routing domain B. Devices that connect over the same LAN must share the same IP address network portion C. Devices on the same VLAN - also known as virtual LAN - or wireless network require separate subnets D. Devices separated by a router need to be on the same common subnet https://www.learncisco.net/courses/icnd-1/ethernet-lans/challenges-of-shared-lans.html Which QoS feature is typically used outbound to an ISP to reduce the amount of traffic that is dropped by exceeding the purchased rate? A. Traffic shaping B. Traffic policing C. Traffic limiting D. Traffic classification Which of the following is the static default route for IPv6? A. 0/:: B. FF::/1 C. ::/1 D. ::/0 You have implemented DAI on a Layer 2 switch in your network. Now you want to monitor the ARP message rates with an average of four received ARP messages a second. Which command(s) would need to be utilized to accomplish this? (Choose two) A. ip arp inspection limit rate 8 burst interval 2 B. ip arp inspection limit rate 4 burst interval 2 C. ip arp inspection limit rate 10 burst interval 5 D. ip arp inspection limit rate 20 burst interval 5 Which protocol number represents ICMPv6? A. 89 B. 88 C. 17 D. 1 E. 58 F. 6 Which command stores passwords as an SHA-256 or MD5 hash? A. service password-encryption B. service password-encryption {sha256 \| md5} C. enable password {sha256 \| md5} D. enable hash-password E. None of the above. Which DSCP Assured Forwarding value provides the worst drop and worst queue performance? A. AF41 B. AF43 C. AF11 D. AF13 Refer to the exhibit; in which area would R1’s Gi0/0 interface be placed? A. 5 B. 6 C. 10 D. 11 Which of the following behaviors are applied to a low latency queue in a Cisco router or switch? (Choose two) A. Shaping B. Policing C. Priority scheduling D. Round-robin scheduling An enterprise plans to start using a public cloud service, and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: What are the possible consequences of an STP failure? (Choose two) A. Only the users that are directly connected to the switch will be affected B. Every port will transition to a blocking state C. The load on all links in the switched LAN quickly starts increasing D. Due to very high load for the CPU, the switch becomes unreachable Host A and Host B sit in two different subnets. The path between the subnets of these two hosts runs through three different Layer 3 forwarding devices (routers and Layer 3 switches). A network engineer uses the APIC-EM Path Trace ACL Analysis tool to analyze the path used for Host A to send packets to Host B. Which part of the function is done specifically by the ACL Analysis or ACL Trace part of the tool? A. Discovery of the topology that exists between the two hosts B. Analysis of the Layer 3 forwarding decisions in the path from Host A to B C. Analysis of the Layer 2 forwarding decisions in the path from Host A to B D. Analysis of the impact of ACLs on the packets that would flow from Host A to B Suppose two APs are located near each other. Which channel use strategy will result in nonoverlapping channels for Wi-Fi use? (Choose two) A. Use 2.4-GHz channel 1 on AP-A and channel 2 on AP-B. B. Use 2.4-GHz channel 1 on AP-A and 5-GHz channel 48 on AP-B. C. Use 5-GHz channel 36 on AP-A and channel 40 on AP-B. D. Use 5-GHz channel 36 on AP-A and channel 37 on AP-B. Which is true in a spine-leaf architecture? (Choose two) A. Each leaf switch must connect to every spine switch. B. Each leaf switch must connect to one spine switch. C. Each spine switch must connect to every leaf switch. D. Each spine switch must connect to one leaf switch. Which cloud service model is primarily targeted toward the software development community and provides the ability to not only customize the hardware being virtualized but also offer different development tools and utilities that are commonly used for a specific environment? A. TaaS B. IaaS C. SaaS D. PaaS What will happen if a private IP address is assigned to a public interface connected to an ISP? A. Addresses in a private range will be not be routed on the Internet backbone. B. Only the ISP router will have the capability to access the public network. C. The NAT process will be used to translate this address to a valid IP address. D. A conflict of IP addresses happens, because other public routers can use the same range. https://www.learncisco.net/courses/icnd-1/building-a-network/tcpip-internet-layer.html Which commands are used to enable a router interface and configure it with the IPv4 address 10.1.1.1/26? (Choose two) A. no shutdown B. ip 10.1.1.1 255.255.255.192 C. address 10.1.1.1 255.252.255.192 D. shutdown E. enable F. ip address 10.1.1.1 255.255.255.192 Why must you subtract two addresses when determining the number of usable addresses within a subnet? (Choose two) A. The last address is the directed broadcast address, which can be used to communicate with all devices in the LAN from another LAN B. The first address is the directed broadcast address, which can be used to communicate with all devices in the LAN from another LAN C. The first address is the subnet ID; and routers use it to make forwarding decisions D. The last address is the subnet ID; and routers use it to make forwarding decisions Which two link protocols are used to carry multiple VLANs over a single link? (Choose two) A. VTP B. 802.1q C. IGP D. ISL E. 802.3u https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html What type of banner should you configure when you want the message to be displayed anytime a user is required to enter usernames and passwords for management sessions? A. incoming B. motd C. login D. EXEC What are the key characteristics of OSPFv3? (Choose two) A. The OSPFv3 metric is based on interface costing B. OSPFv3 omits the use of multiarea network designs with area border routers, or ABRs, that segment the network C. Link-state advertisements, or LSAs, are not flooded throughout an OSPF domain D. IPv6 uses OSPFv3 rather than OSPFv2 https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/ospfv3-configuration.html If a lightweight AP provides at least one BSS for wireless clients, which one of the following modes does it use? A. Local B. Normal C. Monitor D. Client What steps are involved in configuring IPv4 extended access lists? (Choose three) A. Create an extended named ACL B. Apply the ACL globally to the router C. Apply the ACL to an interface D. Specify the conditions to permit or deny packets E. Ensure that the ACL ends with a Deny ALL statement What is the wildcard mask equivalent of the subnet mask /23? A. 0.0.0.1 B. 0.0.3.255 C. 0.0.1.255 D. 0.0.0.0 E. 0.0.0.3 F. 0.0.7.255 G. 0.0.0.7 What Inter-VLAN routing method uses a single physical link between a router and a switch? A. Layer 3 Switch B. Router with separate interfaces for each VLAN C. Router on a Stick D. Multilayer Switch A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch? A. More collision domains will be created. B. IP address utilization will be more efficient. C. More bandwidth will be required than was needed previously. D. An additional broadcast domain will be created. https://www.learncisco.net/courses/ccna/part-5-virtual-lans-vlans/vlans-review.html Which DSCP marking group was created to be backward compatible with Internet Protocol Precedence (IPP) values? A. EF B. AF C. CS D. PF What should be checked when troubleshooting IPv6 end-to-end connectivity? (Choose three) A. Incorrect default gateways B. Physical location of devices C. Physical connection issues D. Blocked traffic from ACLs Which hash method is used by default when using the enable secret Cisco IOS command? A. 3DES B. MD5 C. SHA-0 D. HMAC Which command displays information about security options configured on an interface? A. show port-security interface [interface-id] B. show port-security [interface-id] C. show port-security[address] D. show security [interface-id] enable secret [password] is hashed using the _______ algorithm. A. MD5 B. AH C. PSK D. ESP E. WPA2 Which of the following reserved IPv4 addresses is used in DHCP assignment process before a host has a valid IP address? A. Local broadcast address B. Loopback address C. Directed broadcast address D. Network address E. All zeros address https://www.learncisco.net/courses/ccna/part-2-ip-addressing-and-subnetting-nat/network-addressing.html Which features are used to extend the lifetime and usefulness of IPv4 networks? (Choose four) A. Private Addressing B. VLSM C. CIDR D. VLANs E. Public Addressing F. NAT G. IPv6 Which configuration mode would you use to configure a particular port on a switch? A. Controller configuration mode B. User EXEC mode C. Global configuration mode D. Interface configuration mode https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html You are subnetting the 172.16.0.0/16 network so that you have 100 subnets. How many bits do you need to borrow, what is the new subnet mask, and how many hosts will be in each subnet? (Choose three) A. There will be 254 possible hosts in each subnet B. There will be 510 possible hosts in each subnet C. /23 is the new subnet mask D. 7 bits will be borrowed E. 8 bits will be borrowed F. /24 is the new subnet mask What are some of the wireless LAN controller (WLC) capabilities? A. Security management B. Dynamic RF management to assign channels to APs C. RF monitoring to gather information about the channel D. Ease of deployment by programming all RF policies and wireless LAN policies on all APs E. All of these are correct. What is the name of the Cisco product that offers a number of rack-mountable server configurations intended to be used in data centers? A. ASA B. KVM C. CRC D. UCS From the following options, what are the required REST API attributes? (Choose two) A. JSON-formatted data B. Unlayered systems C. Layered systems D. Client-server architecture You want to verify the Cisco IOS software version, ROM version, amount of memory, type of processor, number and types of interfaces, as well as the configuration register value on your 2900 series IOS router. What command will allow you to accomplish this? A. Show startup-configuration B. Show running-configuration C. Show version D. Show flash When are VTP messages sent to clients for synchronization while using a VTP server? (Choose two) A. Every five minutes by default B. Every ten minutes by default C. Only when manually triggered D. Any time there is a change R3 has a static route configured that points toward the service provider. What command could you use to have R3 advertise an OSPFv3 default route to the internal network, regardless of whether R3 had its default static route? A. The decision to advertise a default route depends on the static route always being present on R3. B. The default behavior is to redistribute any default IPv6 routes into OSPFv3, so no action is required. C. Each of the other routers needs a static default route that leads to R3. D. Use the command default-information originate always in interface mode for G1/0 on R3. E. Have R3 use the command default-information originate always in OSPFv3 router configuration mode. What is the destination address of a router solicitation packet? A. FF02::2 B. FF02::A C. FF02::9 D. FF02::6 E. FF02::1 F. FF02::5 For what two purposes does the Ethernet protocol use physical addresses? (Choose two) A. to uniquely identify devices at Layer 2 B. to allow communication with devices on a different network C. to differentiate a Layer 2 frame from a Layer 3 packet D. to establish a priority system to determine which device gets to transmit first E. to allow communication between different devices on the same network F. to allow detection of a remote device when its physical address is unknown https://www.learncisco.net/courses/icnd-1/ethernet-lans/packet-delivery-process.html Which statements correctly define unique local unicast addresses? (Choose two) A. They are not routable B. They are identified by the prefix FE80::/10 C. They are identified by the prefix 2000::/3 D. They are identified by the prefix FC00::/7 E. They are routable in your private network F. They are globally routable

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources